Learn about fossil preparation in our FREE handy guides!

£4.95

DISCOUNTS: 

ADD ANY THREE 20g SUPERGLUES TO CART TO GET 10% OFF (including low, mid, high and gel viscosity)

OR ADD ANY THREE 50g SUPERGLUES TO CART TO GET 10% OFF (including low, mid and high viscosity)

A structural adhesive for industrial-strength general purpose bonding. This high-performance medium viscosity cyanoacrylate is a great all-rounder for joining surfaces together. This is one of the most useful and versatile superglues to have on hand. 120 cP viscosity which is approximately the same as a thin motor oil.

All surfaces to be bonded must be clean, dry, oil and grease free. Apply a thin film to one surface only and bring together immediately. Clamp or hold tight for a few seconds. Once aligned, the components cannot be reset without debonder. Initial set in seconds. Full cure after 24 hours.

20g or 50g bottle.

  • Guaranteed Safe Checkout

THE ZOIC PALAEOTECH RANGE OF FOSSIL, ROCK & MINERAL CYANOACRYLATES

The ZOIC PalaeoTech range are non-yellowing, non-blooming and industrial strength superglues for use in fossil preparation. If you want to find out more about using cyanoacrylates in fossil preparation, read our guide! Good quality superglues are high purity, and designed to age well without going brittle or producing white blooms. We have a full range of cyanoacrylates of all viscosities for different jobs, as well as a specific low-stain activator (to speed up setting) and debonders (to remove superglue from your fingers and to aid removal of superglue). 


LOW VISCOSITY SUPERGLUE

Low viscosity superglue for consolidation and stabilising cracks in rocks, fossils and minerals. This is a very low viscosity cyanoacrylate (very close to the viscosity of water). Sets in seconds. Viscosity: 5CP.


Sizes available: 20g, 500g. 

  • Perfectly suited for permanent consolidation and stabilisation of rocks, fossils and minerals, plasticising the any pore it gets into. It utilizes wicking or capillary action for deep penetration into small cracks and any porous rock – i.e. it pulls itself into small spaces.

  • Ideal for use when joining extremely closely fitting parts and smooth, even surfaces.

  • Great for consolidating hairline fractures or holding thin, flaky material in place during the process of fossil preparation.

  • Can also be used to help prevent pyrite decay by sealing a fossil from the atmosphere via minute pore fill to prevent further oxidation and therefore pyrite decay.


MEDIUM VISCOSITY SUPERGLUE

A structural adhesive for industrial-strength general purpose bonding. This high-performance medium viscosity cyanoacrylate is a great all-rounder for joining surfaces together. This is one of the most useful and versatile superglues to have on hand.

  • Fast setting

  • Strong and durable

  • Suitable for both porous and absorbent matrices, with some gap filling properties – it will fill small pores along the join.

  • 120 cP viscosity which is approximately the same as a thin motor oil.


HIGH VISCOSITY SUPERGLUE

A structural adhesive for industrial-strength bonding where run-off needs to be controlled. A high viscosity cyanoacrylate is particularly useful for pore and gap filling. Rapid setting, but a slightly slower set time than the medium and low viscosities allowing a few seconds for alignment of pieces. Spray with our Quick-Set Superglue Activator once you are happy with the position to set instantaneously.

  • Fills wider cracks and holes where necessary.

  • 1500 cP viscosity which is approximately the same as gloss paint.

  • Suitable for long-lasting repairs and for bonding very porous surfaces.

  • Use where it is necessary to prevent the glue from running or spreading.



EXTRA-THICK GEL SUPERGLUE

A non-dripping structural adhesive for industrial-strength bonding. This extremely high viscosity cyanoacrylate adhesive gel is highly suited to gluing vertical surfaces without dripping. 


It dries a little more slowly than the other cyanoacrylates and so gives time to align and set all pieces together correctly, allowing approximately 1 minute of working time. The bond can usually be separated by hand after 2-3 minutes if required. Allow to set for a minimum of 10-15 minutes. Use our Quick-Set activator spray to instantly set the outer edges of the bond in place so that you don't have to hold it or clamp it!

  • Extremely useful for gap and void filling.

  • Suitable for long-lasting repairs and for bonding very porous surfaces.

  • The tube with its tapered tip and the extra thick consistency of the glue allow you to apply just the right amount in just the right place.

  • Use where it is necessary to prevent the glue from running or spreading.


CYANOACRYALATE DEBONDERS (SPECIFIC TO THE ZOIC PALAEOTECH RANGE)

GEL DEBONDER

SHAKE EXTREMELY WELL BEFORE USING. This product is thixotropic and will appear to be solid until agitated. Upon shaking, it will suddenly transform in front of your eyes into a gel-like consistency which allows for a lot of control in application.


Brilliant for removing the superglue that somehow gets on your skin no matter how careful you have been! If you have a habit of attaching yourself to what you're gluing, this is an essential for your workshop.

LIQUID DEBONDER

Brilliant for removing the superglue that somehow gets on your skin no matter how careful you have been! If you have a habit of attaching yourself to what you're gluing, this is an essential for your workshop.


If used to remove glue from skin, allow debonder to penetrate the bond line for 60-120 seconds and rub in with fingertips. On rocks and fossils, removal may take longer after application or repeat applications may be required for thick glue or a deep bond line. Allow glue to soften which can then be scraped away. Clean the surface of the rock or fossil with isopropyl alcohol and a lint free cloth.


LOW-STAIN ACTIVATOR SPRAY

**UK MAINLAND SHIPPING ONLY**

Activator spray to instantly set superglue in place. Put the clamps away and let our non-yellowing formula do the job! Can be used with the entire range of ZOIC PalaeoTech cyanoacrylates.

  • Accelerates setting time of superglue

  • Increases bond strength on very porous substrates

  • Use sparingly and allow to evaporate

Whilst the slowed setting time of higher viscosity glues can be exceptionally useful, sometimes once you’ve got your pieces into place you just want them to set. By spraying on a little activator, you can accelerate the curing reaction to set the bond in place instantly. Most activators are associated with a yellow-staining. We use a very low staining formula for this very reason, but we would still recommend you test first on pale coloured fossils or rocks.

Customer Reviews

Based on 1 review Write a review